Lumber, roof, span and fastener tables

Ceiling Joist Span Chart

Pick a joist size, spacing, wood species and attic load to see the maximum ceiling joist span, the limit that governs, and a chart of every size and spacing.

Open on FramingDesk

Embed

Embed this tool

Copy this code into your website, blog or class page. The tool runs inside your page.

Please keep the credit link below the tool.

The ceiling joist span chart on this page shows how far a ceiling joist can run between supports for the size, species and grade, spacing, and attic load you choose. You pick a lumber species and grade, a size from 2x4 to 2x10, a spacing of 12, 16, 19.2 or 24 inches, and an attic load. The page then gives the maximum span and a chart covering all four sizes at all four spacings. It runs in your browser, nothing is uploaded, there is no sign-up, and it is free. The result is calculated from your inputs, using the same method as the floor joist page, and it shows which of three limits governs. It is a planning reference, not a substitute for an engineer, an inspection or a permit.
Ceiling joist span chart example

How to use the Ceiling Joist Span Chart

  1. Choose the “Species and grade” you plan to use. The default is Douglas fir-larch No. 2.
  2. Choose the “Ceiling joist size (nominal)”: 2x4, 2x6, 2x8 or 2x10. The default is 2x6.
  3. Choose the “Joist spacing, on center (in)”: 12, 16, 19.2 or 24. The default is 16.
  4. Set the attic load in “Live load (psf)” and “Dead load (psf)”, or use a preset: “No storage, 10+5” (the default, with a live-load deflection limit of span / 240), “Storage, 20+10”, or “Plaster ceiling, ÷ 360” (deflection limit span / 360).
  5. Read the maximum span. Spans are rounded down to the whole inch and shown in feet and inches with metres.
  6. Check the “Limit that governs”. The default result is 17’-8", governed by live-load deflection, while bending allows 18’-4".
  7. Scan the chart for all four sizes at all four spacings. Cells longer than 26 ft read “over 26 ft”, and the letter after each span names the limit that governs it. Any span over 20 ft carries a warning about lumber supply, so check what lengths your supplier carries.
  8. Read the assumptions and the structural note under the result. They say the result is not a substitute for an engineer, an inspection or a permit.

If your lumber has different design values, choose “My own design values” under species and grade and type your bending value Fb, shear value Fv and modulus of elasticity E. To try a different case, change one input at a time and compare the results.

How is a ceiling joist span calculated?

A ceiling joist span is the longest distance a joist can cross before one of three limits is reached: bending strength, shear strength, or live-load deflection. The tool works out each limit and reports the smallest one, because that limit governs the span.

Bending uses L = sqrt(8 Fb’ S / w). Fb’ is the adjusted bending design value, S is the section modulus of the joist, and w is the total load per foot of joist, which is the load in pounds per square foot multiplied by the spacing in feet. Shear uses L = 4 A Fv’ / (3 w), where A is the cross-sectional area and Fv’ is the adjusted shear design value.

Deflection uses L = cbrt(384 E I / (5 w_live n)). E is the modulus of elasticity, I is the moment of inertia, and w_live is the live load per foot. The value n sets the deflection limit as span / n. The tool uses n = 240 for ceilings with gypsum board and span / 360 for plaster. The design values come from AWC Table W-1 for bending, adjusted for size with the repetitive-member factor of 1.15 included, and from the NDS Supplement for shear and E. You can also enter your own values.

Which limit sets the ceiling joist span in the default case?

Deflection limits how much the joist sags, while bending and shear are strength limits. The code lists span / 240 for ceilings with gypsum board and span / 360 for plaster.

The default case shows deflection governing. A 2x6 at 16 inches with 10 psf live and 5 psf dead load, limited to span / 240, gives a result of 17’-8" that is governed by live-load deflection. Bending alone would allow 18’-4". Changing the size, spacing or attic load can change which limit is smallest, so compare the three limits each time you change an input.

The calculation assumes a simple span, a uniform load, a braced top edge, dry service, three or more joists at 24 in or less, no roof thrust on the ceiling joists, no notches, holes or point loads, and it does not check bearing. If your ceiling differs, the number does not apply directly, and the page is not a substitute for an engineer, an inspection or a permit.

Sources (checked 15 October 2026): awc.org · web-media.awc.org · up.codes · cityofsacramento.gov · awc.org · awc.org · web-media.awc.org · up.codes

Worked examples

InputResult
2×6, Douglas fir-larch, No. 2Maximum span 17'-8", governed by Deflection under live load (span ÷ 240)
2×8, Southern pine, No. 2Maximum span 12'-5", governed by Bending
2×4, Hem-fir, No. 2Maximum span 10'-6", governed by Deflection under live load (span ÷ 240)
2×10, Spruce-pine-fir, No. 1 / No. 2Maximum span 21'-8", governed by Deflection under live load (span ÷ 360)

Calculated by the tool above; open it with the same values to see each step.

Frequently asked questions

What span does a 2x6 at 16 inches get with the default settings?

With Douglas fir-larch No. 2, 10 psf live and 5 psf dead, and span / 240, the default result is 17’-8". Live-load deflection governs this result, and bending allows 18’-4".

Why does a cell read “over 26 ft”?

Chart cells longer than 26 ft show “over 26 ft” instead of a number. The chart is meant to show that the span is long, not to give an exact figure above that length.

Why is my span one inch lower than the published table?

Published span tables round to the nearest inch, while this page rounds down. A value can therefore be one inch below the published one. Checked against the published code tables, all 96 No. 2 cells of IRC R802.5.1(1) and (2) for 2x4 to 2x8 came out equal to or one inch below the published value, and none came out above it.

Does this tool tell me whether my ceiling passes?

No. The page shows the three limits and which one governs, but it gives no pass or fail verdict. The result is calculated from your inputs, and the structural note under it says the result is not a substitute for an engineer, an inspection or a permit.

Why does the page show a lumber supply warning?

Any span over 20 ft carries a warning about lumber supply. Long lengths may be harder to find at your local yard, so check availability before you plan a layout that depends on them.

Which design values does the tool use?

Bending uses the size-adjusted Fb from AWC Table W-1, and shear and E come from the NDS Supplement, unless you enter your own values. AWC Table W-1 lists E at 1,200,000 psi for Hem-fir No. 2 2x6 and 2x8, while NDS Table 4A lists 1,300,000 psi. This page uses 1,300,000 psi, which matches the published IRC span tables, and takes only Fb from Table W-1.